Can I Set Up a Tub Myself? Considerations And Also Steps
Can I Set Up a Tub Myself? Considerations And Also Steps
Blog Article
Just how do you actually feel about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bath tub isn't exactly brain surgery, but it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably challenging project. If the old bathtub is readily easily accessible, the project can relocate speedily; if you need to open a wall surface to remove the old bathtub as well as position the brand-new bathtub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub and set in the brand-new one. Ensure you have actually qualified yourself for the work and fit attempting it. Rather than employing a service provider to take over a halfway-completed task, it is better to think about using one before you start. Chances are you may need an expert plumber to make tube links.
This short article will certainly aid you install a brand-new bath tub in your shower room if you have already acquired a new tub as well as do not require to change the plan of your previous water pipelines.
Your tools as well as product list ought to make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, then the first thing you must do is detach the water. After doing so, turn on the taps to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be fairly problematic due to the restricted gain access to that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly originate from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing compound.
Before proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin making certain that the washing machines remain in location between the faucet and also the sink. Protect the tap in place with the supplier supplied backnut. Once the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous type should be attached to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Making use of both wood boards under its feet, place the bath tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
The following goal is to make certain that the bathtub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the tub until the level reads degree.
To install taps, fit all-time low of the furthest adaptable tap connector to the proper supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Switch on the water system and check all joints as well as new pipework for leakages and tighten them if needed. Fill the bath tub and likewise check the overflow electrical outlet and the typical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bathtub must wait until the tub has actually been used a minimum of when as this will certainly resolve it into its last placement.
Preparing for the Setup
Firstly, the supporting framework provided with the bath should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps system to stop pressure on the bathtub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last setting.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall in between the bathroom and also the tiling, causing issues with moisture as well as possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes and cartridges, and also can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the bath tub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealant can crack fairly very early if you do not take into account this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently offered on the market. It is suggested to fit the floor tiles utilizing waterproof or water-proof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very focused on A Step-by-Step Guide to Installing a Bathtub and I am hoping you liked our entry. In case you appreciated our post please be sure to share it. Thank-you for taking the time to read it.
More Details
Report this page